長毛兔的兔毛從采集到非常終成為高檔紡織品，需要經過一系列科學、嚴謹的加工工序。整個加工過程主要可以分為以下幾個核心階段：

The rabbit hair of the long haired rabbit needs to go through a series of scientific and rigorous processing procedures from collection to final production into high-end textiles. The entire processing process can be mainly divided into the following core stages:

一、 兔毛的采集與預處理

1、 Collection and preprocessing of rabbit hair

兔毛的采集質量直接決定了后續加工的價值。目前非常主流且快捷的方法是電動剪毛，這種方式不僅效率高、不留多余雜毛，還能有效保護兔子的皮膚不受損傷3。此外，也有部分采用梳毛或手拔的方式，但手拔對兔子的傷害較大，已逐漸被淘汰6。

The quality of rabbit hair collection directly determines the value of subsequent processing. The most mainstream and efficient method currently is electric shearing, which not only has high efficiency and leaves no excess hair, but also effectively protects the rabbit's skin from damage. In addition, some use combing or hand pulling methods, but hand pulling can cause significant damage to rabbits and has gradually been phased out.

剪下的兔毛在收集時，通常會采用吊掛式剪毛法，讓剪下的毛自然落入下方的尼龍袋中，以保持兔毛原有的毛型不亂，從而賣出更好的價格4。收集后的兔毛會根據色澤、長短和潔凈度進行人工分揀。例如，未被弄臟的深毛品質非常好，而腳掌周邊受污染的毛發則被視為下腳料。

When collecting the cut rabbit hair, the hanging shearing method is usually used to allow the cut hair to naturally fall into the nylon bag below, in order to maintain the original hair shape of the rabbit hair and sell it at a better price. The collected rabbit fur will be manually sorted based on color, length, and cleanliness. For example, unpolished deep fur has the best quality, while contaminated fur around the soles of the feet is considered as waste.

二、 機械分梳（提取兔絨）

2、 Mechanical combing (extracting rabbit fur)

剛剪下的兔毛是粗毛（槍毛）與細毛（絨毛）的混合物。為了獲得出彩其柔軟的“兔絨”，需要進行機械分梳。兔絨是通過特制的梳絨設備，將兔毛中的粗毛和槍毛剔除，只保留底部非常細軟的絨毛。

The freshly cut rabbit hair is a mixture of coarse hair (gun hair) and fine hair (fluff). In order to obtain extremely soft "rabbit fur", mechanical combing is required. Rabbit fur is made by using a specially designed combing device to remove coarse and gun hair from rabbit fur, leaving only the thinnest and softest fur at the bottom.

這一過程對設備要求出眾。兔毛需要經過8到10遍的反復梳理，使粗細分開、長短分離?，F代先進的梳絨技術會將氣流分梳與齒輥梳理相結合，并嚴格控制車間的溫濕度，以減少對兔絨纖維的損傷。經過精細分梳后，出絨率一般在20%左右，得到的兔絨細度出彩?。s13-14微米），品質優于國家標準6。

This process requires extremely high equipment requirements. Rabbit hair needs to be repeatedly combed 8 to 10 times to separate thickness and length. Modern advanced combing technology combines air flow combing with toothed roller combing, and strictly controls the temperature and humidity in the workshop to reduce damage to rabbit wool fibers. After fine combing, the velvet yield is generally around 20%, and the obtained rabbit velvet has a very small fineness (about 13-14 microns), far exceeding the national standard of 6.

三、 紡紗與織造

3、 Spinning and Weaving

由于兔毛纖維表面光滑、卷曲少且纖維之間抱合性能差，純紡兔毛較為困難。因此，在紡織加工中，兔毛大多與其他纖維進行混紡，或者采用精紡純兔絨工藝1。

Due to the smooth surface, minimal curling, and poor adhesion between fibers of rabbit hair, pure spinning of rabbit hair is relatively difficult. Therefore, in textile processing, rabbit hair is mostly blended with other fibers or processed using precision spun pure rabbit velvet technology.

經過紡紗工序后，兔毛或兔絨會被加工成紗線，進而織造成針織衫、機織面料、呢類大衣以及高檔毛毯等紡織品1。

After the spinning process, rabbit hair or rabbit fur is processed into yarn, which is then woven into textiles such as knitwear, woven fabrics, woolen coats, and high-end blankets.

四、 后道整理工藝

4、 Post finishing process

兔毛制品在穿著過程中容易出現“掉毛”現象，這主要是因為其表面光滑、抱合力差造成的。因此，后期的整理技術至關重要。現代紡織工業會采用防掉毛的整理技術、高染色牢度的染色技術以及差別化功能整理技術，來非常大程度地改善兔絨織物的掉毛問題，提升產品的耐用性與舒適度6。

Rabbit hair products are prone to shedding during wearing, mainly due to their smooth surface and poor grip. Therefore, post-processing techniques are crucial. The modern textile industry adopts anti shedding finishing techniques, high color fastness dyeing techniques, and differentiated functional finishing techniques to minimize the shedding problem of rabbit velvet fabrics and enhance the durability and comfort of products.